What're your beliefs about A Step-by-Step Guide to Installing a Bathtub?

Installing a bath tub isn't specifically brain surgery, but it does require solid plumbing, carpentry, and also often, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably tough task. If the old bathtub is conveniently accessible, the project can relocate speedily; if you have to open a wall surface to get rid of the old tub and place the brand-new bath tub, the task is much harder. In either case, the job is within a residence handyman's abilities, although you will need an assistant to leave the old bathtub as well as embeded in the new one. Make certain you have actually qualified yourself for the task and also are comfortable attempting it. As opposed to working with a specialist to take control of a halfway-completed task, it is better to think about utilizing one prior to you start. Opportunities are you might require a professional plumber to make tube links.
This short article will certainly help you mount a brand-new tub in your shower room if you have already bought a brand-new bathtub as well as don't need to transform the plan of your previous water pipelines.
Your devices as well as product checklist ought to comprise the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, then the first thing you need to do is separate the supply of water. After doing so, turn on the taps to drain any water continuing to be in the system. The procedure of removing the existing faucets can be quite problematic because of the limited gain access to that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will come from the pipes. As soon as the supply pipes have been removed, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning during this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Prior to going on to fit the new faucets, compare the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the installing opening in the bath/basin ensuring that the washers are in area between the tap as well as the sink. Secure the faucet in place with the manufacturer offered backnut. As soon as the tap is firmly in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former kind needs to be connected to the faucet ends first, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Utilizing the two wood boards under its feet, place the bathtub in the required placement. The wooden boards are helpful in evenly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four little factors.
The next goal is to ensure that the tub is leveled all round. This can be attained by checking the spirit level as well as adjusting the feet on the bath tub up until the spirit level reviews level.
To install taps, fit all-time low of the furthest adaptable tap connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other tap.
Activate the water supply and also check all joints and also new pipework for leaks and also tighten them if necessary. Fill the tub and additionally examine the overflow electrical outlet and the normal electrical outlet for leaks.
Lastly, repair the bath paneling as explained in the maker's instruction manual. Tiling and also sealing around the bathtub should wait up until the bathtub has been made use of a minimum of when as this will certainly settle it right into its last placement.
Planning for the Setup
First of all, the sustaining framework provided with the bathroom ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the tap features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets device to stop strain on the bathtub.
Fit the flexible tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you use every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.
Tiling Around the Bath tub
In the location where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to crack an inflexible seal, causing the water to permeate the wall surface in between the bath and the tiling, causing difficulties with wetness and feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures as well as fittings. They are offered in tubes and cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to always load the bath tub with water prior to sealing, to enable the activity experienced when the bathtub is in use. The sealant can split fairly very early if you do not take into consideration this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly offered on the market. It is a good idea to fit the ceramic tiles using water-resistant or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

I hope you enjoyed reading our piece on How to Install a Bathtub. Thank you so much for taking the time to read through our article. Are you aware of somebody else who is enthusiastic about the subject? Please feel free to promote it. We value reading our article about How to Install a Bathtub.
Leak? Reach out!